Thursday, April 28, 2011

Lampu depan


tu hari gua outstation, tgh kt highway ada la 1 lori kan main laju bwk cm haram. kalau takat pasir2 terbang ok lg, tp ni batu besar2 guli tu melantun sebelah gua. ngam2 dia potong je, kena sebijik kt keta gua. mula2 gua ingt kena body, then bila smpi hotel gua check2 tgk...ayaakk!! lampu gua pecah. dlm hati gua dok maki pemandu2 lori yg bwk cm haram kat highway. gua contact member sruh cri kn lampu kt kedai halfcut. xsampi 2jam gua dpt kol kata jumpa dh lampu yg gua nk tu. blk je dgn pantas gua kasi bukak lampu, kasi pasang. skali dh pasang lg 1 masalah. bila gua tgk lmpu gua ke dalam sket.

Bila gua belek2, rupanya ada gak beza utk model2 saga. yg gua dpt dr member tu model magma which is nipis sket. smentara gua pnye orien sama dgn megavalve yg mana lampu dia tebal&kaki utk lampu kecik tepi pn lain..gua pn runner p cari lampu baru kt spare part&ganti balik..so yg salah tu gua tolak kt member gua since dia pn nk pakai..ho ho ho..

front&rear mounting



Apa fungsi mounting pd enjin? Simple; untuk menyokong enjin supaya melekat pd body. Betul ke tidak ayat gua pn xsure, tp tu la yg bg sng org faham. Kalau mounting pd pd enjin lu org sudah xkuat atau "terlebih kuat", enjin lu org blh jatuh. Sbb gua ada jumpa kes dimana ketidaksesuaian enjin yg di convert pd sesebuah kereta menjadikan enjin tersebut jatuh&menjahanamkn body kereta yg dok tampung enjin tu. So berhati2 dlm ubahsuai enjin. Sbb banyak benda yg kena diambil perhatian dr segi keselamatan&sebagainya.

Bg keta buruk cm gua, mounting standard dh memadai. Utk pemilihan mounting, bg yg nk bikin sndiri, kena tau jenis kereta&model. sbb mounting berbeza utk setiap jenis model. contoh; orien, magma, megavalve berbeza2 bentuk&saiz. Silap beli, mmg xblh masuk sbb tapak yg lain. Tp kebanyakan mounting utk depan, biasanya mmg standard blh masuk utk mane2 saga. (tgk gambor)

manakala bg yg belakang, kiri&kanan adalah berbeza mengikut jenis model. lupa gua nk bgtau, utk saga biasa ada 4 mounting utk pegang enjin lu org. Gua start bikin mounting mlm since siang gua agk sibuk. blh dikatakan payah terutama yg bahagian belakang since gua punye power steering besar. Gua prasan sbb mse pomen nk masukkan mounting belakang tu dlu mmg payah since steering rack gua agak besar banding dgn yg asal. (tgk entry power steering projek). Cite banyak xguna. yg penting gua dpt pengalaman sendiri. Apapun thanks pd member gua yg sama tlg gua memprojekkan mounting keta gua.

mounting lame smpi koyak getah dia


new mounting


Tuesday, April 5, 2011

4G93T GSR


Aiyyak..ni dh masuk bulan april oo..tp azam2 gua masih gk x dicapai. agak2 bila la gua nk dpt "duit terpijak" eh? Ni salah 1 enjin favourite gua gk. Gua jumpa info utk tatapan lu org. Dlm english k? Info ni bagus utk semua. Credit to ben the owner of the 4g93T.


Since Malaysia government had changed the rules and regulation for engine conversion, which all Proton cars except Proton Perdana cannot convert to 2.0L engine, the Mitsubishi Lancer GSR 4G93T is one of the highest horsepower turbo engine that can fit into Proton cars (only applicable for those who wish to register their car to JPJ and legally on the road). From the topic, it is clearly shows that this is the first generation 4G93T GSR 1.8L from the Mitsubishi Lancer. There are two types of engine specification throughout the entire life of the Mitsubishi 4G93T first generation engine. There are the normal version which capable to produce approximately 190hp and the 4G93T RS from the wagon also known as Libero in Malaysia here which able to produce approximately 210hp.

Below are some of the specification of the GSR 1.8L RS.
1. Body: wagon
2. HP: 210bph on flywheel

GSR 1.8RS specs.:
Displacement : 1834 cc
Engine model : 4G93T (turbo)
Max.power (Net),: 150.78kw(205PS)/ 6000rpm
Max.torque(Net): 28.0 kg*m (274.59 N*m) / 3000 rpm

Engine type Water cooling serial 4 cylinder DOHC16 valve IC turbo
Engine information :
Fuel system ECI multiple (electrically controlled gasoline injection)
Turbocharger Turbo with intercooler
Fuel type Unleaded premium gasoline
LEV system (Low emission vehicle) No
Compression ratio : 8.5
Bore : 81mm
Stroke : 89mm

Here are the normal GSR 4G93T specification. Almost all the GSR in Malaysia are this specification.

Technical Specifications:
TURBO SYSTEM
Make - IHI
Model No - TD04L-13G-5
Waste gate opening pressure - 78 kPa

FLUID CAPACITIES (litres)
Engine oil pan(with filter) - 4.0
Engine oil pan(without filter) - 3.8
Manual transaxle -1.8
Engine coolant - 5.0
Reserve tank - 0.7
Fuel tank - 50
Power steering - 0.9
Transfer case - 0.5
Rear differential - 0.8

Manual Transaxle
Hypoid Gear Oil; API classification GL-4 (preferred) or higher
viscosity No. SAE 75/85W, 80W

Rear differential
Gear Oil; API classification GL-5 or higher
viscosity No. SAE 90W or 80W

Transfer
Gear Oil; API classification GL-4 or higher
viscosity No. SAE 75W-85W, 80W

Power steering
Dexron II Automatic transmission fluid

Engine coolant
Mitsubishi Long Life Coolant at the specified concentration by mixing with demineralised or rainwater only.

Front and rear Wheel bearings
Lithium Base "Multi-purpose" E.P No.2 grease

DIMENSIONS (mm)
Overall length -4275
Overall width mm -1690
Overall height mm -1385
Wheelbase mm - 2500

Track
- Front -1450
- Rear -1460
Ground clearance mm (unladen) -150
Turning circle - kerb to kerb -10.2m
Seating capacity -5

MASS (Kg). This is only applicable for Lancer. For those who convert this engine to Proton Satria, Proton Saga the weight is different compare to Lancer and Wira.
Kerb Mass (with tank of fuel)
1190
GMV
1680
GCM
2430

Air Conditioning
+20
Power Steering
+6
Tow Bar
+15
Anti Skid Braking
+17

GMV = Vehicle Mass + Payload
GCM = GMV + Trailer and Load

TORQUE SPECIFICATIONS(Nm) .
Cylinder head bolts
- hot engine
80-85
- cold engine
t 20 + ¼ + ¼
Camshaft sprocket bolts
90
Camshaft bearing caps
- M6
11
- M8
24
Main bearing cap bolts
*25 + ¼
Crankshaft pulley to sprocket
12-15
Connecting rod cap nuts
*20 + ¼
Crankshaft sprocket bolt
185
Flywheel/drive plate crankshaft bolts
100
t = Tightening angle method after initial tension to 75 Nm then completely loosened.
* = Tightening angle method

GENERAL ENGINE DATA
Engine
1.8litre
Model
4G93
Type
16v Double Overhead Cam
Bore mm
81
Stroke mm
89
Displacement cc 1834
1834
Power Rating DIN 70020
141kW @ 6000 RPM
Torque Rating DIN 70020
249Nm @ 3000 RPM
Compression Ration
8.5:1
Compression Pressure
935kPa
Firing Order
1-3-4-2
Valve clearance (hot)
- Inlet mm
Auto
- Exhaust mm
Auto
Valve Timing Intake Valve Opens BTDC
19deg
Intake Valve Shut ATDC
53deg
Duration
253deg
Spark Plug Type
NKG BK6E
Bosch F7DC
Nippondenso K20P-U
Spark Plug Gap mm
0.7-0.8
ECI Engine timing (with terminal grounded)
5deg BTDC +- 2deg
Idle speed rpm
750+-100

NOTE On vehicles fitted with a catalytic converter a blackened exhaust pipe is a normal condition.

COOLING SYSTEM
Thermostat opens
77 deg C
Radiator cap release pressure
75 to 105 kPa

TRANSAXLE
Type
Manual
Model
W5M33
Gear ratios
5 Speed
1st
2.916
2nd
1.684
3rd
1.115
4th
0.833
5th
0.666
Reverse
3.166

Primary reduction
1.680
Transfer gear
1.090
Final drive gear
- front
2.936
- rear
4.525

BRAKES (mm)
Front
Ventilated Disc
Diameter
204.0
Thickness
- Std mm
24.0
- Min mm
22.4
Lining pad thickness
2.0
Disc run out
0.8
Rear
Solid Disc
Diameter
224.0
Thickness
10.0
Lining pad thickness
2.0
Disc run out
0.8
Wheel speed sensor clearance
- front Fixed
Fixed
- rear
0.3 - 0.9
Master cylinder
Tandem, dual proportioning valve with 'x' split system
Bore diameter
22.2
Booster Master Vac Diameter
180/205
Brake pedal height
162-165
Brake pedal freeplay
3-8
Park brake lever stroke
5 - 7 notches @ 200N

WHEEL ALIGNMENT
Front suspension
McPherson strut, coil spring
Camber (non~adjustable)
0 deg +- 30'
Caster
2 deg 20' +- 30'
Toe-in (measured at centre of tyre tread)
0 +- 3mm
Toe-in Angle
0 deg +-0 deg 9'
Toe-out angle on turns when outer wheel at 20'
21 deg 12'
King-pin inclination
12 deg 49'
Rear suspension
Trailing arm multi link
Camber
0 deg 40' +- 30'
Toe-in (at rim)
0.5 +- 2.5 mm

STEERING GEAR
Type
Rack and pinion
Steering wheel free play
10-30 mm

CLUTCH
Type
Single diaphragm with single dry disc
Diameter
215 x 140 mm
Pedal free play
6 - 13 mm
Pedal height
162 - 165 mm
Release bearing
Self centering type

WHEELS AND TYRES
Wheels
14" x 5.5" JJ
Tyre
195/60R14 85V
Pressure
- Front
210kPa
- Rear
200-210 kPa
Rim runout max lateral\radial
1.0 mm

ELECTRICAL
Battery
272 CCA 49 minutes
Alternator
12v with integrated voltage regulator
Output
65 A

FUEL SYSTEM
Type
Multipoint electronically controlled
Fuel pump
Electric in tank
Pressure
335 kPa
Fuel type
Unleaded petrol only

LinkWithin

Related Posts with Thumbnails